Shurup Posted August 2, 2013 Share Posted August 2, 2013 Is it possible to lower the seat height by 10 cm or so? Thinking Ninja 250 or 300 or possibly cbr250. Changing the tires and rims will drop it down a bit but I wouldn't want to put too small tires on it. Any other options? Link to comment Share on other sites More sharing options...
Neilly Posted August 2, 2013 Share Posted August 2, 2013 I know they do a lowering option for the CRF250L....CRF250M lowered....enough? Link to comment Share on other sites More sharing options...
Shurup Posted August 2, 2013 Author Share Posted August 2, 2013 (edited) Crf is a dirt bike, its way to tall to begin with. The bikes I mentioned, Kawasakies, seat height is 790 mm dropping it down to 700 will do. It's for a GF who just can't reach the ground. She can ride my chopper which is about 650 mm or so, and her brother's Chinese dirt bike which is a bit taller but she still can reach the ground, I will measure its seat height tonight. Edited August 2, 2013 by Shurup Link to comment Share on other sites More sharing options...
Gsxrnz Posted August 2, 2013 Share Posted August 2, 2013 I don't know the specific bike, but have lowered bikes before. Depends why you want to lower it - handling or comfort. Lowering by 2-4 cm will not alter the handling too much but will generally make a bike turn in quicker at speed. You can lower the front by say 2-4cm and no need to lower the rear. but you won't get the lower seat height you want. Lowering as much as 10cm is actually quite a bit. You can drop the triple tree down and have the forks come through, provided there's no obstruction. If the suspension is a single you can fit "dogbones" to reduce the height. If it's double rear swingarm mounted, you can buy smaller units. But...10cm is a lot and if you achieve it all through suspension and tyre height you'll find the bike very different to handle. Try a combination of 2-4cm on the suspension, and taking some foam off the seat, plus lower profile tyres and/or smaller rims. 1 Link to comment Share on other sites More sharing options...
Shurup Posted August 2, 2013 Author Share Posted August 2, 2013 10 cm was just a guess, I think you're right and it's a little too much to do. Might not actually need that much, have to measure that Chinese bike first. Or maybe I will just get her few of these: Will be easier and faster and cheaper... just need to figure out how to stick one underneath the shifter... Link to comment Share on other sites More sharing options...
Shurup Posted August 2, 2013 Author Share Posted August 2, 2013 OK the Chinese dirt bike is 77 cm high (the seat) but the bike is very narrow so its easier to reach the ground, comparing with the same height seat on a wider bike. Anyways I think that all it needs to be lowered is 3-4 cm, maybe proper riding boots will take 1 cm away from that... What do you think folks the best way to lower it 3-4 cm? Will I need to do the from and the rear or only one of them? Link to comment Share on other sites More sharing options...
macknife Posted August 2, 2013 Share Posted August 2, 2013 Brian at Sumet lowered a CBR250 and can provide the service. Maybe he will notice this thread and give you some advice or send him a PM. Just from what I know, the front shocks can be lowered on those bikes but you may have to change/alter the 'handlebars'. You can get low profile tires too. Link to comment Share on other sites More sharing options...
Jerry Cornelius Posted August 2, 2013 Share Posted August 2, 2013 I'm not being contentious, I've read the post and I just wonder why would you want to lower the bike. It's pretty low already. Jerry Link to comment Share on other sites More sharing options...
KRS1 Posted August 2, 2013 Share Posted August 2, 2013 - 2 cm from seat foam height - 2 cm from seat foam width - 2 cm from suspension sag on softest setting. - 1 cm from lower triple clamp (will reduce wheelbase) - 1 cm from wearing boots - 1 cm @ 30psi tires - 0.5 cm with full tank of gas - ??? cm from weight of rider Link to comment Share on other sites More sharing options...
Jerry Cornelius Posted August 2, 2013 Share Posted August 2, 2013 - 2 cm from seat foam height - 2 cm from seat foam width - 2 cm from suspension sag on softest setting. - 1 cm from lower triple clamp (will reduce wheelbase) - 1 cm from wearing boots - 1 cm @ 30psi tires - 0.5 cm with full tank of gas - ??? cm from weight of rider w.r.t. what? Understand most of what your alluding to, but seat width! How will this affect ride height? The X factor (rider mass) is the real factor (especially if wearing boots {2 to 4 kg = -1cm} is valid). Why would one want to sink lower? On such a light bike, what is gained? Jerry Link to comment Share on other sites More sharing options...
jbrain Posted August 2, 2013 Share Posted August 2, 2013 - 2 cm from seat foam height - 2 cm from seat foam width - 2 cm from suspension sag on softest setting. - 1 cm from lower triple clamp (will reduce wheelbase) - 1 cm from wearing boots - 1 cm @ 30psi tires - 0.5 cm with full tank of gas - ??? cm from weight of rider w.r.t. what? Understand most of what your alluding to, but seat width! How will this affect ride height? The X factor (rider mass) is the real factor (especially if wearing boots {2 to 4 kg = -1cm} is valid). Why would one want to sink lower? On such a light bike, what is gained? Jerry Because when seat is smaller, the legs are less spread and the feet come lower. 1 Link to comment Share on other sites More sharing options...
Jerry Cornelius Posted August 2, 2013 Share Posted August 2, 2013 - 2 cm from seat foam height - 2 cm from seat foam width - 2 cm from suspension sag on softest setting. - 1 cm from lower triple clamp (will reduce wheelbase) - 1 cm from wearing boots - 1 cm @ 30psi tires - 0.5 cm with full tank of gas - ??? cm from weight of rider w.r.t. what? Understand most of what your alluding to, but seat width! How will this affect ride height? The X factor (rider mass) is the real factor (especially if wearing boots {2 to 4 kg = -1cm} is valid). Why would one want to sink lower? On such a light bike, what is gained? Jerry Because when seat is smaller, the legs are less spread and the feet come lower. But the mass applied to the suspension is equal. Yes? Link to comment Share on other sites More sharing options...
Phatcharanan Posted August 2, 2013 Share Posted August 2, 2013 (edited) I'm not being contentious, I've read the post and I just wonder why would you want to lower the bike. It's pretty low already. Jerry You must have missed reading post #3 then. Edited August 2, 2013 by Phatcharanan 1 Link to comment Share on other sites More sharing options...
BSJ Posted August 3, 2013 Share Posted August 3, 2013 Aside from the lowering which can be done, how about changing the shifter to a push button setup. All you need are 3 solenoids, some brackets and 2 momentary switches.....and some electrical wiring. Vola! Push button gear changes. Link to comment Share on other sites More sharing options...
Shurup Posted August 3, 2013 Author Share Posted August 3, 2013 ^^^ do you mean in conjunction with the platform shoes? I showed her the shoes and she slapped me, I don't think she likes them, nor me making jokes about her height. LOL Sent from my GT-I9100 using Thaivisa Connect Thailand mobile app Link to comment Share on other sites More sharing options...
KRS1 Posted August 3, 2013 Share Posted August 3, 2013 - 2 cm from seat foam height - 2 cm from seat foam width - 2 cm from suspension sag on softest setting. - 1 cm from lower triple clamp (will reduce wheelbase) - 1 cm from wearing boots - 1 cm @ 30psi tires - 0.5 cm with full tank of gas - ??? cm from weight of rider w.r.t. what? Understand most of what your alluding to, but seat width! How will this affect ride height? The X factor (rider mass) is the real factor (especially if wearing boots {2 to 4 kg = -1cm} is valid). Why would one want to sink lower? On such a light bike, what is gained? Jerry lower center of gravity. any modifications that do with seat height will always change handling characteristics. seat width is as jbrain stated, and should also be reduced when cutting the height to try and keep similar leverage on the hips as the original seat. Link to comment Share on other sites More sharing options...
jbrain Posted August 3, 2013 Share Posted August 3, 2013 I had a friend in my homecountry who had a Yamaha Roadliner 1900 and had an aftermarket hydraulic suspension installed, which would lower the bike with just a push on the button. It even could be operated by remote control, however he soon found out that it wasn't a good idea to keep the remote in his front pocket while riding the bike 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now