zappalot Posted December 3, 2016 Share Posted December 3, 2016 This ceiling is underneath a bathroom. We let set new tiles in the bathroom above. But what is best advice to apply new cement to the now exposed steel? Link to comment Share on other sites More sharing options...
Lamkyong Posted December 3, 2016 Share Posted December 3, 2016 as the rebar seems to already 50 pc corroded i would suggest nothing apart from demolition would be a safe repair sure cement will stick to it but you are just hiding the inevitable demise of the structure and hopefully not anybody that may be in its proximity Link to comment Share on other sites More sharing options...
kannot Posted December 3, 2016 Share Posted December 3, 2016 holy ship, thats seriously bad work.................to be expected though Link to comment Share on other sites More sharing options...
eyecatcher Posted December 3, 2016 Share Posted December 3, 2016 Thats a great photo to show why you need your 20mm of cover around reinforcement. In your case they have just dropped the fabric meash directly onto to the ply shutters (ply? maybe I am being optimistic) and poured away. Regardless of the condition of the reinforcement I would expect (hope) there to be 100mm depth of concrete so personally I wouldn't be unduly concerned unless you start inviting elephants around for a piss up. The rebar is there as a secondary measure to reinforce the underside, the part thats in tension so only a catastrophic failure of each bar would put the connie at any risk. Bad practice, hell yes, but why has it corroded. what room is that? another shower room thats had years of humidity? or was the floor above never ever tiled. Simple enough task to protect the steel again.....can start with some primer red oxide just to stop the steel corroding further; can even shove some ply back up to the underside; can skim it, but the easiest/best method is to gyproc it on battens or a metal grid in line with those concrete beams and it will of course hide that blue pipework along the way. I have to ask.....there's an old water feed pipe adjacent the sink waste, is it cut off? whats the story? Link to comment Share on other sites More sharing options...
eyecatcher Posted December 3, 2016 Share Posted December 3, 2016 5 hours ago, Lamkyong said: as the rebar seems to already 50 pc corroded i would suggest nothing apart from demolition would be a safe repair sure cement will stick to it but you are just hiding the inevitable demise of the structure and hopefully not anybody that may be in its proximity How did you reach the conclusion that the rebar is 50% corroded. I wonder if also you can see what diameter the rebar is? Link to comment Share on other sites More sharing options...
Lamkyong Posted December 3, 2016 Share Posted December 3, 2016 2 hours ago, eyecatcher said: How did you reach the conclusion that the rebar is 50% corroded. I wonder if also you can see what diameter the rebar is? Link to comment Share on other sites More sharing options...
AJBangkok Posted December 4, 2016 Share Posted December 4, 2016 If you don't want to do anything about the steel then just mix some lanko 751 with the new motar and splash some on the existing cement to be covered and it will bond. Your floor may collapse in a few years when the rebar fails but the cement will stick on. Link to comment Share on other sites More sharing options...
zappalot Posted December 4, 2016 Author Share Posted December 4, 2016 Thank you very much for everyone's input. We will evaluate what to do and post the results in two or three months :-) Link to comment Share on other sites More sharing options...
eyecatcher Posted December 4, 2016 Share Posted December 4, 2016 Don't forget to update us in 2 month and the betting odds are as follows: 1/2 OP not yet got his finger out 2/1 OP bought red primer and left it a that. 3/1 OP heeded advice, protected the steel and installed a new ceiling. 10/1 OP about to post new thread "how to repair cracks in concrete floor 33/1 OP posts photos of collapsed floor 50/1 OP decided to "sod it" and moved out instead. Link to comment Share on other sites More sharing options...
kannot Posted December 15, 2016 Share Posted December 15, 2016 On 12/4/2016 at 7:34 PM, eyecatcher said: Don't forget to update us in 2 month and the betting odds are as follows: 1/2 OP not yet got his finger out 2/1 OP bought red primer and left it a that. 3/1 OP heeded advice, protected the steel and installed a new ceiling. 10/1 OP about to post new thread "how to repair cracks in concrete floor 33/1 OP posts photos of collapsed floor 50/1 OP decided to "sod it" and moved out instead. 100/1 op is dead crushed by falling floor! Link to comment Share on other sites More sharing options...
cheeryble Posted December 16, 2016 Share Posted December 16, 2016 Rust itself forms a protective layer against more rust......in varying degrees depending on the conditions. If you get a sturdy penknife or the like a try scraping into the rust it's possible you'll find the rebar has clean steel just below the surface. The best way to remove damp source is to re-mortar the tile bed and coat well with two part epoxy, the lower grade stuff easily available. Run the epoxy up the wall a couple of inches. to form a waterproof pan. (The rust may also have come from condensation of steam filled bathroom over years.) If repeat if you've removed the source of damp from above and there's shiny steel just below the rebar surface I'd do nothing. The underside of the concrete which came off or was never there has no strength function as it's the tension side, only to seal the rebar. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now