jacko45k Posted June 25, 2021 Share Posted June 25, 2021 16 hours ago, jomtienisgood said: It is not necessary to change anything on the electrical supply grid.. The mains are everywhere 3 X 380/400V+N. therefor in between each phase and N you obtain 220/240V. ( almost everywhere in the world ). However it would be virtually impossible ( due to cost ) to convert the USA system... 110V... May sound like unnecessary but bare in mind Ohms Law. Different frequency too..... Link to comment Share on other sites More sharing options...
jomtienisgood Posted June 26, 2021 Share Posted June 26, 2021 3 hours ago, jacko45k said: Different frequency too..... Yes, I didn't mention that, but now you do , 50/60Hz. Link to comment Share on other sites More sharing options...
jomtienisgood Posted June 26, 2021 Share Posted June 26, 2021 6 minutes ago, jomtienisgood said: Yes, I didn't mention that, but now you do , 50/60Hz. And I also didn't mention: W ( watt )/V (volt )=A ( amps ). Where this is important is that( in the USA vs the rest of the world ), due to lower Voltage the Amperage goes up. This again being important because the Heat induction is not Linear but logarythmic. Everyone follow?????? Link to comment Share on other sites More sharing options...
actonion Posted June 26, 2021 Share Posted June 26, 2021 Earlier this year i ran across Second Road from Mikes shopping Mall to Kiss & food Restaurant, outside that Restaurant is an eEectric post which i grabbed to slow myself from running, and received an Electric shock from that post, Waitress in that Restaurant said many people complain about it ... ( but noting done) Link to comment Share on other sites More sharing options...
jomtienisgood Posted June 26, 2021 Share Posted June 26, 2021 1 hour ago, actonion said: Earlier this year i ran across Second Road from Mikes shopping Mall to Kiss & food Restaurant, outside that Restaurant is an eEectric post which i grabbed to slow myself from running, and received an Electric shock from that post, Waitress in that Restaurant said many people complain about it ... ( but noting done) That is in order to reduce your heart beats rate after all the running..???? Link to comment Share on other sites More sharing options...
jomtienisgood Posted June 27, 2021 Share Posted June 27, 2021 23 hours ago, jomtienisgood said: And I also didn't mention: W ( watt )/V (volt )=A ( amps ). Where this is important is that( in the USA vs the rest of the world ), due to lower Voltage the Amperage goes up. This again being important because the Heat induction is not Linear but logarythmic. Everyone follow?????? My apologies to the ones reading this. Yesterday I used the term ' logarythmic ' whereas it should say : ' Exponential ' . Experiencing some IT problems for the moment, my brain was confused.... Link to comment Share on other sites More sharing options...
thaibeachlovers Posted June 27, 2021 Share Posted June 27, 2021 On 6/25/2021 at 10:50 PM, Led Lolly Yellow Lolly said: Be careful here, hospitals are a special case. They usually have completely different electrical systems due to the nature of the site and the medical equipment used. Flammable gases, oxygen, explosive situations, complex medical imaging equipment. This is a very specialised area of electrical engineering. Most hospitals have the same electrical voltage throughout. Link to comment Share on other sites More sharing options...
Led Lolly Yellow Lolly Posted June 27, 2021 Share Posted June 27, 2021 (edited) 3 hours ago, thaibeachlovers said: Most hospitals have the same electrical voltage throughout. It doesn't matter, the underlying ground system is usually different, often an IT ground (Isolé-Terre, not Information Technology) where the transformer is intentionally isolated from the ground rather than bonded to it. The voltage is irrelevant to that. As I said, it's complicated. The reason for this is you don't want breakers tripping power during surgery, and you don't want ground loop noise on diagnostic equipment, all kinds of issues in hospital environments. Edited June 27, 2021 by Led Lolly Yellow Lolly Link to comment Share on other sites More sharing options...
thaibeachlovers Posted June 28, 2021 Share Posted June 28, 2021 On 6/27/2021 at 8:24 PM, Led Lolly Yellow Lolly said: It doesn't matter, the underlying ground system is usually different, often an IT ground (Isolé-Terre, not Information Technology) where the transformer is intentionally isolated from the ground rather than bonded to it. The voltage is irrelevant to that. As I said, it's complicated. The reason for this is you don't want breakers tripping power during surgery, and you don't want ground loop noise on diagnostic equipment, all kinds of issues in hospital environments. It mattered to me when one of the transformers we had to use to convert 110v to 240v fell on my foot. Rather heavy, it was. Link to comment Share on other sites More sharing options...
jomtienisgood Posted June 28, 2021 Share Posted June 28, 2021 48 minutes ago, thaibeachlovers said: It mattered to me when one of the transformers we had to use to convert 110v to 240v fell on my foot. Rather heavy, it was. How about PPE ???? 1 Link to comment Share on other sites More sharing options...
jacko45k Posted June 29, 2021 Share Posted June 29, 2021 16 hours ago, thaibeachlovers said: It mattered to me when one of the transformers we had to use to convert 110v to 240v fell on my foot. Rather heavy, it was. Could you step-up after? 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now