Jump to content

Recommended Posts

Posted
  On 9/21/2019 at 10:05 AM, maxcorrigan said:

Trouble is i have not been able to install anything from a USB until i have cleaned off all the stuff i have on the laptop hence the dban each time which takes 8 1/2 hrs

Expand  

DBAN is overkill. Your trouble is booting from USB which is easier when there is nothing to boot from because of DBAN. You can press "ESC" right after you power on the laptop and then choose to boot from USB. If this fail you can also choose to boot from USB via the BIOS menu. 

Posted
  On 9/21/2019 at 10:29 AM, Tayaout said:

Here is a thread about your graphic card (same laptop) : https://forums.linuxmint.com/viewtopic.php?t=282645

 

I will take the time to read it but seems like older version works fine.

 

The paths of least resistance at this point seem to be Linux Mint 18.03

Expand  

Yes exact same model laptop and Sylvia seems the way to go, so goodbye Tina!

Thanks for your hard work and unceasing effort, you have pinpointed the exact problem. if i manage to install 18.03 it should work, but cannot afford to update correct?

Posted
  On 9/21/2019 at 11:23 AM, maxcorrigan said:

If i manage to install 18.03 it should work, but cannot afford to update correct?

Expand  

Hard to tell without trying. The thread say you need to login to cinnamon with hardware acceleration disabled. Mate and XFCE desktop seems to have better performance. The last post pointed out that your model of graphic card is losing support from the Linux kernel. If you choose to update and have the same issue you can usually boot with an older kernel from the grub menu. 

  • Like 1
Posted
  On 9/21/2019 at 12:13 PM, Tayaout said:

Hard to tell without trying. The thread say you need to login to cinnamon with hardware acceleration disabled. Mate and XFCE desktop seems to have better performance. The last post pointed out that your model of graphic card is losing support from the Linux kernel. If you choose to update and have the same issue you can usually boot with an older kernel from the grub menu. 

Expand  

Update! Mint 18.3 booted straight away from USB have downloaded it after many freeze ups which has wiped 19.2, after downloading it said PC must restart which it did, just got to do some setting up now, first tried to download side by side but stated there was a problem, so had to re-install, will see about up-dating later, so we have proved a point, so thank you Tayaout once again you've been a great help!

Posted
  On 9/21/2019 at 12:59 PM, maxcorrigan said:

Update! Mint 18.3 booted straight away from USB have downloaded it after many freeze ups which has wiped 19.2, after downloading it said PC must restart which it did, just got to do some setting up now, first tried to download side by side but stated there was a problem, so had to re-install, will see about up-dating later, so we have proved a point, so thank you Tayaout once again you've been a great help!

Expand  

First problem keeps freezing up which means a restart every time!

Posted
  On 9/21/2019 at 7:51 PM, Tayaout said:

Did you login selecting software rendering in the drop down menu? 

Expand  

Where is that, i just went through the procedure language, wi-fi etc. then it would freeze, start again freeze again a little bit further each time till i got it installed, then would freeze up again in use, am now going to download again using mint mate instead of cinnamon see if that helps!

Posted
  On 9/22/2019 at 4:11 AM, maxcorrigan said:

Where is that, i just went through the procedure language, wi-fi etc. then it would freeze, start again freeze again a little bit further each time till i got it installed, then would freeze up again in use, am now going to download again using mint mate instead of cinnamon see if that helps!

Expand  

Has'nt made much of a difference still freezing in "mint mate", Selected software rendering i believe i got through holding alt during startup chose >advanced >recover mode >open linux mint if that is what you were referring too, it has'nt made any difference though still freezes

Posted
  On 9/22/2019 at 5:53 AM, Stocky said:

What?!!? - no need, a clean install will overwrite everything anyway!

 

.

Expand  

It would not boot from USB tried many many times, the only way was wipe the disk, even then took a lot of persuading to boot mint 19.2, but with mint 18.3 boots every time from USB or HDD and does all the overwriting  needed, only trouble now is it freezes a lot which so far needs a re-start each time!

Posted
  On 9/22/2019 at 7:40 AM, maxcorrigan said:

It would not boot from USB tried many many times, the only way was wipe the disk, even then took a lot of persuading to boot mint 19.2, but with mint 18.3 boots every time from USB or HDD and does all the overwriting  needed, only trouble now is it freezes a lot which so far needs a re-start each time!

Expand  

I'm 99% confident your freezing problem is an issue with the video driver. Your card is old and use proprietary driver. AMD since then has moved to an open source model that make it easier to get support from the Linux kernel. Try an older version of Mint if you don't mind.

  • Like 1
Posted
  On 9/22/2019 at 8:42 AM, Tayaout said:

I'm 99% confident your freezing problem is an issue with the video driver. Your card is old and use proprietary driver. AMD since then has moved to an open source model that make it easier to get support from the Linux kernel. Try an older version of Mint if you don't mind.

Expand  

OK will try that!

Posted
  On 9/22/2019 at 5:07 AM, maxcorrigan said:

Has'nt made much of a difference still freezing in "mint mate", Selected software rendering i believe i got through holding alt during startup chose >advanced >recover mode >open linux mint if that is what you were referring too, it has'nt made any difference though still freezes

Expand  

Update on Mint Mate been running for over three hours with no freeze, probably saying that will probably make it freeze solid next time i start, here's hoping!

Posted
  On 9/22/2019 at 12:21 PM, maxcorrigan said:

Update on Mint Mate been running for over three hours with no freeze, probably saying that will probably make it freeze solid next time i start, here's hoping!

Expand  

You will be fine! 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.




  • Topics

  • Popular Contributors

  • Latest posts...

    1. 11

      Thailand Live Thursday 15 May 2025

    2. 0

      Social Media Tattoo Artist “Namwan Laiphrang” Arrested in Drug and Firearms Raid

    3. 11

      Thailand Live Thursday 15 May 2025

    4. 34

      Another Lazada scam story

    5. 0

      Defence Secretary Stands by Military Leaders Amid Afghan War Crimes Allegations

  • Popular in The Pub

×
×
  • Create New...